I´ve been wondering how to do this kind of shadows (image below) as real as possible. Is there any technique to apply? I did search for tutorials but unfortunately I couldn´t find anything on this specific topic.
1In my experience, realistic shadows are one of the more complicated things to grasp. But because you are illustrating something in the isometric style, you should have grids that help you with your shadow. There isn't an automated way to do this, just define your light source location and make every shadow adhere to that angle. For this style they all have to be drawn. youtube.com/watch?v=tHpEMktKLlM– CmdZzzMar 13, 2017 at 15:21
@CmdZzz in my experience a isometric grid just slows you down.– joojaaMar 13, 2017 at 15:47
Doing accurate shadows is quite easy, albeit a bit tedious. All you need is to do is to systematically find intersections of lines. Not all that different from drawing (or constructing) the original orthographic or perspective images in the first place.
Before we begin lets define two different shadow models:
Directional lights, are light sources that are very far away, like the Sun (about 150 million kilometers away). They cast shadows that are parallel to each other*.
Point light sources, lights that are closer and thus have a central source.
These are quite idealized models, there are others, but should be sufficient for your needs. The example image you show is displaying a directional shadow.
* A 1 kilometer wide object (two of the largest oil tankers end to end) would have 0.004 degree angle deviation form parallel between edges of the shadow if you would model the sun as a point light. This seems close enough to parallel.
Image 1: Directional shadows made in illustrator. To see construction lines look here.
I will begin by describing directional shadows, because they are slightly simpler (or faster) to construct than point lights. Mainly because you can share the construction line.
Start by constructing your isometric scene. Keep in mind that you may need to deduce the height of objects later. So doing some bookkeeping may help you later, so store relevant info in a notes layer.
The basic idea is to find the intersection of a line and a plane, virtual or otherwise. We do this by first deicing the direction of the shadow and one corner on the primary (ground) plane.
Image 2: The light direction, and the light direction on the floor plane. As well as deconstruction of the XYZ moves to verify that the light makes sense.
Store the construction shape as it will help you solve problems you didn't anticipate. Its especially useful when you start having more height levels, if not then all you need is the light direction line.
For each corner on shadow casting side on same height duplicate the direction line. Then connect the lines and the points on the shadow casting edges on ground. You may need to construct the invisible sides to get the appropriate directions (or use the line direction on ground plane)
Image 3: Simplest case. Area bounded by lines and cast shadow is called shadow volume.
To understand better how the bottom side works, and why we saved the directions let us look at a still quite simple case where the object is hovering above the ground. Now our direction line isn't long enough anymore, we need to extend it. But how much?
This is where the direction on ground line comes into play. You draw the vertical down to ground level, Then place the direction on ground line on this point, the ground lies at intersection of the extended direction line and the direction on ground line. The intersection is where the ground plane intersects with direction line.
Image 4: By building triangles of verticals and ground direction lines you can measure nearly any intersection.
Ok, so this is tedious. But there is a easier way, for planar objects. If we think of the cube only having the top and bottom face you will notice that the shadows of the objects are the same shape as the top and bottom piece just offset from the original. Because the planes are co-planar and the projection does not have nonlinear changes.
Image 5: More complicated planar objects are easier. Objects co-planar to the shadow catching object are just offset.
A similar method applies to side faces only you may need to use a few skews rotates and a scale to achieve it (it is related to the SSR method of constructing objects). Lets look at what a square surface does and skew a object surrounded by square to same shape.
Image 6: Side panel projected. Due to the nature of things if you can project a square you can project anything in a square
All this means that the kind of example that you have presented takes a few minutes and requires only a few alt drags of objects. However you need to know what your doing. Far too complex subject for most easy tutorials.
Image 7: Same illustration point light shadows.
Point lights work similarly, with the change that the rays of light emanate from a point. This means that there is no trick to finding the points. Its all finding rays ad their intersection.
So what you do is you draw a line from the light source to every shadow casting corner. Then you draw a line from the light ground to the corresponding ground corner. You then extend the lines (with say transform each by scaling up) and find each intersection.
Image 8: Point light construction. Extend rays to corners form light location and its corresponding ground point.
That is it, other then tricks on extending lines theres not much you can automate beyond this.
Extending to Perspective
Perspective works like point light shadows, for both light types. This is because even co-linear lines are emanating form points in perspective. So the workflow is the same for both types of light.
Now, knowing this has many utilities outside 2D drawing packages too. Its pretty common to need to do this line direction calculation when tracking live scenes for 3D graphics. Also the light models are the same as used in 3D.
Also note that: I do not use grids. The line tool, and alt drag cloning, is good enough for finding intersections. The grid just artificially constrains me to certain size decisions and ultimately does not make the job easier. But then I am trained as a mechanical engineer.
2Buddy, I´m very thankful... this is the answer that I´ve been looking for. Although, it looks hard to apply, I gonna practice it to master it. Thank you so much May 17, 2017 at 19:27
@germanolivera its not hard just tedious (do not mix these things, hard problems are truly intractable, complex problems just require patience) added a few sentences on how to make point lights and how to deal with perspective.– joojaaMay 20, 2017 at 17:45
Shadow geometry - here's one method for Adobe illustrator. It's strictly limited to parallel projections - no pespective! There's no math, all is by eye. But the proportions and angles come out right.
This all is a little easier in Photoshop because there you have easy to use distortion that fits this like a fist into your eye. (Edit > Transform > Distort)
I recommed to test also the distortion in Photoshop. It unfortunately forces to draw some quide lines because you have a little too much possiblities.
Seriously: A complex scene that contains a mass of quite simple objects is much easier to create with highlights and shadows in 3D design software. Highlights, shadows and the wanted perspective come out with no work at all when the model is entered.
Interested? Check at first Trimble SketchUP. It's free. The following image took less than 2 min to create in SketchUP.
The ladder truck is taken from Trimble's 3D warehouse.